Everbuilt Pre-Plumbed Sewage Basin System 1/2 HP 6500 GPH Review

Dealing with basement flooding or sewage backup isn’t just messy—it’s stressful, costly, and potentially hazardous to your health. If you’re looking for a dependable, all-in-one solution that simplifies installation and delivers powerful performance, the Everbuilt Pre-Plumbed Sewage Basin System 1/2 HP 6500 GPH might be exactly what your home needs. Designed for both residential and light commercial use, this system combines efficiency, durability, and ease of setup in one ready-to-install package.

What Is the Everbuilt Pre-Plumbed Sewage Basin System?

The Everbuilt Pre-Plumbed Sewage Basin System 1/2 HP 6500 GPH is a complete wastewater removal unit engineered for homes without gravity-fed sewer access—common in basements, cottages, or areas below the municipal sewer line. Unlike standard sump pumps that handle only clean water, this system is built to manage raw sewage containing solids up to 2 inches in diameter.

Key components include:

• A heavy-duty polyethylene basin (typically 18″–22″ diameter)
• A 1/2 horsepower cast iron sewage pump
• Pre-installed discharge piping with check valve
• Integrated alarm system (on select models)
• Watertight lid with gasket seal

This “pre-plumbed” design means much of the plumbing is factory-assembled, drastically reducing on-site labor and potential installation errors.

💡 According to the U.S. Environmental Protection Agency (EPA), over 23,000 sewage overflows occur annually in the U.S. due to pump failures or inadequate systems. Choosing a reliable unit like Everbuilt’s can prevent costly backups and health risks.

How Does It Work? (Step-by-Step Operation)

Understanding how the system functions helps homeowners appreciate its reliability:

1. Wastewater Entry: Sewage from toilets, sinks, or laundry flows into the basin via inlet pipes.
2. Float Activation: As liquid rises, an internal float switch triggers the 1/2 HP pump once the preset level (usually 9–12 inches) is reached.
3. Pumping Action: The pump activates, pushing wastewater through the pre-installed 2″ discharge pipe at a rate of 6,500 gallons per hour (GPH) at 5 feet of head pressure.
4. Check Valve Protection: A built-in check valve prevents backflow, ensuring sewage doesn’t re-enter the basin after pumping.
5. Automatic Shut-Off: Once the water level drops, the float deactivates the pump, conserving energy and extending motor life.

This cycle repeats automatically—no manual intervention needed.

Key Features & Benefits

✅ All-in-One Convenience

No need to source individual parts. The basin, pump, piping, and fittings come pre-assembled, saving 3–5 hours of labor compared to DIY setups.

✅ Handles Solids Up to 2 Inches

Unlike sump pumps, this sewage ejector pump grinds and moves waste containing toilet paper, fecal matter, and small debris—critical for full bathroom installations.

✅ Energy Efficient 1/2 HP Motor

While more powerful than typical sump pumps, the 1/2 HP motor consumes only ~9–10 amps, balancing performance with operational cost. Estimated annual electricity cost: $45–$65, depending on usage.

✅ Durable Construction

• Cast iron pump housing: Resists corrosion and handles high temperatures.
• Polyethylene basin: Crack-resistant, non-corrosive, and compliant with ASTM D1998 standards.
• Thermal overload protection: Automatically shuts off if the motor overheats.

✅ Code-Compliant Design

Meets UPC (Uniform Plumbing Code) and IPC (International Plumbing Code) requirements for residential sewage ejection systems—essential for passing inspections.

Everbuilt vs. Competitors: How Does It Compare?

Note: Everbuilt’s biggest advantage is the fully pre-assembled basin—ideal for contractors or DIYers wanting plug-and-play simplicity.

For more on sewage system standards, see Wikipedia’s overview on sewage pumping.

Ideal Use Cases

This system shines in specific scenarios:

• Basement bathrooms: Adding a toilet or shower below sewer grade.
• Barndominiums or ADUs: Accessory dwelling units without direct sewer access.
• Cottages near lakes: Where septic systems require pumped effluent.
• Flood-prone areas: As part of a dual sump/sewage backup plan.

⚠️ Not recommended for continuous high-volume commercial use (e.g., restaurants). Stick to residential or light-duty applications.

Installation Tips (For DIYers & Contractors)

While “pre-plumbed,” proper setup ensures longevity:

1. Place on Level Concrete: Use a rubber mat or gravel base to minimize vibration.
2. Vent the System: Install a 2″ vent pipe tied into your home’s main stack to prevent airlock.
3. Discharge Pipe Slope: Maintain a 1/4″ per foot downward slope away from the house.
4. Electrical Connection: Hardwire to a dedicated 120V GFCI-protected circuit (do not use an extension cord).
5. Test Before Backfilling: Run 5–10 gallons of water mixed with toilet paper to verify pump activation and discharge flow.

🛠️ Pro Tip: Add a battery backup (like the Basement Watchdog BW4000) for power outage protection—critical during storms when sewage backup risk peaks.

Maintenance Checklist

To extend system life (most last 7–10 years with care):

• Monthly: Pour 1 gallon of vinegar down the drain to reduce odor and buildup.
• Quarterly: Inspect float switch movement—ensure it’s not stuck or tangled.
• Annually: Remove the pump and clean impeller with a soft brush; check for cracks in the basin.
• Every 3 Years: Replace the check valve (wear item) even if functioning.

Ignoring maintenance can lead to clogs, motor burnout, or silent failure—often discovered only during a flood.

FAQ Section

Q1: Can this pump handle toilet waste?

Yes. The Everbuilt 1/2 HP 6500 GPH is specifically rated for blackwater (toilet waste) and can pass solids up to 2 inches—standard for residential sewage ejectors.

Q2: What’s the maximum pumping height (head lift)?

At 10 feet of vertical lift, flow drops to ~4,200 GPH. For lifts over 15 feet, consider a 3/4 HP model. Always consult the pump curve chart before installation.

Q3: Is a separate alarm system needed?

Most Everbuilt kits include a basic high-water alarm. For added security, upgrade to a Wi-Fi-enabled alert system (e.g., HydroCheck HC2) that notifies your phone.

Q4: Can I install this myself?

Handy homeowners can install it in 4–6 hours if familiar with plumbing and electrical work. However, local codes often require a licensed plumber for sewage connections—check with your municipality first.

Q5: What size generator do I need for backup power?

A 1,500-watt generator is sufficient to run the pump during outages (startup surge: ~1,200W; running: ~800W).

Q6: Does it qualify for insurance discounts?

Some insurers (like State Farm or Liberty Mutual) offer premium reductions for homes with certified sewage backup prevention systems. Ask your agent!

Conclusion

The Everbuilt Pre-Plumbed Sewage Basin System 1/2 HP 6500 GPH delivers peace of mind through smart engineering, robust construction, and unmatched ease of installation. Whether you’re finishing a basement bathroom or safeguarding against sewage floods, this system offers professional-grade performance without the complexity.

Don’t wait for a backup to strike—proactive protection saves thousands in cleanup and repairs.

Found this guide helpful? Share it on Facebook, Pinterest, or Reddit to help other homeowners stay dry and safe! 💧🚽🔧